欢迎访问济南宁达建材有限公司!

济南宁达建材有限公司

联系人:李经理

电话:15954121087

移动电话:15153190187

地址:山东省济南市天桥区小清河北路滨河商务中心D座24层2402

当前位置:首页>新闻动态>>常见问题>>济南卫生间隔断的施工准备以及要点

济南卫生间隔断的施工准备以及要点

来源:http://www.jnndjc.com 日期:2022-06-25 发布人:nsadmin
卫生间隔断的施工准备
Construction preparation of toilet partition
1、材料及安装工具:
1. Materials and installation tools:
(1)进入现场的隔板样式、数量及加工质量符合设计要求,有出厂合格证。
(1) The style, quantity and processing quality of diaphragms entering the site shall meet the design requirements, and the factory certificate shall be provided.
(2)五金配件的种类、规格、型号符合图纸要求,并与卫生间隔板相匹配且产品质量合格。
(2) The type, specification and model of hardware fittings shall meet the requirements of the drawing, match with the toilet partition, and the product quality shall be qualified.
(3)安装工具:电锤、改锥、电钻、螺丝刀等。
(3) Installation tools: electric hammer, screwdriver, electric drill, screwdriver, etc.
2、作业条件:
2. Operating conditions:
(1)卫生间隔断进入施工现场必须检查验收,安装前应先检查型号,尺寸是否符合要求。
(1) The toilet partition must be inspected and accepted when entering the construction site. Before installation, check whether the model and size meet the requirements.
(2)现场安装队实行队长负责制,由队长负责统筹协调施工期间的事宜。
(2) The on-site installation team implements the team leader responsibility system, and the team leader is responsible for overall planning and coordination of matters during construction.
(3)严格按照施工程序,确保施工质量。
(3) Strictly follow the construction procedures to ensure the construction quality.
(4)注意卫生间隔断门板的开启方向及测量的尺寸,以确保安装时的门的裁口方向。
(4) Pay attention to the opening direction and measured dimension of the toilet partition door panel to ensure the cutting direction of the door during installation.
卫生间隔断施工要点
Key points of toilet partition construction
(1)现场检查:查看图纸复量尺寸,检查图纸与现场是否相符,检查瓷砖,卫生洁具等相关的成品有无损坏之处,特殊工艺的按照甲方和监理确认的施工图施工。
(1) On site inspection: check the size of the drawing, check whether the drawing is consistent with the site, and check whether the finished products related to ceramic tiles, sanitary ware, etc. are damaged. For special processes, the construction shall be carried out in accordance with the construction drawings confirmed by Party A and the supervisor.
济南卫生间隔断
(2)派线确位:标好墙面尺寸,保持水平,垂直、大片应安在 两坑正中间(或按现场要求操作)。
(2) Setting out and positioning: mark the wall size, keep it horizontal, and install the vertical and large area in the middle of the two pits (or operate according to the site requirements).
(3)安装标高:根据测量的图纸检查卫生间隔断安装的标高尺寸。
(3) Installation elevation: check the elevation dimension of toilet partition installation according to the measured drawings.
(4)配件定位:
(4) Accessory positioning:
按照标高,设计和监理确认通过的五金件(合页、门锁、拉手、支架、横梁)设计确认通过,安支架时保持两边间距尺寸一样,安大片直角时,保证在中间位置(分中),上下两端保持20公分,(直角中心点)根据情况有管道。
According to the elevation, the hardware (hinge, door lock, handle, support and cross beam) confirmed by the designer and the supervisor has passed the design confirmation. When installing the support, the spacing between the two sides shall be the same. When installing the large right angle, ensure that it is in the middle position (in the middle), and the upper and lower ends shall be kept at 20cm (in the center of the right angle) with pipes as the case may be.
腰线应量好尺寸,再开口,缝口不超过0.1厘米(直角), 注意不要打坏墙砖或地砖,安合页时,门上下两端保持20厘米,门下端与中小片高低一样,合页螺丝安装在(打眼时应控制在小于1厘米深度,尔后上螺丝。
The waist line shall be measured and then opened. The seam shall not exceed 0.1 cm (right angle). Be careful not to damage the wall or floor tiles. When installing the hinge, the upper and lower ends of the door shall be kept at 20 cm, and the lower end of the door shall be the same as the height of the small and medium-sized pieces. The hinge screws shall be installed at (the depth shall be controlled at less than 1 cm when drilling holes, and then the screws shall be installed.
安锁时应注意如有台阶锁芯的位置距门下端85厘米,如有残疾人坑,应与有台阶锁位置一样平行,锁一定要端正,灵活自如,锭横梁应在中小片上固定螺丝或钉子,锭塑板或角铝应从反面安圆头螺丝固定,注意塑板与中小片无缝平整。
When installing the lock, it shall be noted that if there is a step lock cylinder, the position shall be 85CM from the lower end of the door. If there is a pit for the disabled, it shall be parallel to the position of the step lock. The lock must be upright and flexible. The spindle beam shall be fixed with screws or nails on the small and medium pieces. The spindle plastic plate or angle aluminum shall be fixed with round head screws from the opposite side. It shall be noted that the plastic plate and the small and medium pieces are seamless and flat.
(5)安装调试:调试固定门缝应2至2.5毫米的距离,小腿固定至少两颗螺丝,门与中小片下端平齐,门的开启轻松自如,回归到位,对隔断门用线进行四边调正,门上下水平垂直,满足施工规范的要求。
(5) Installation and commissioning: adjust and fix the door seam at a distance of 2 to 2.5 mm, fix at least two screws at the lower leg, make the door flush with the lower end of the small and medium-sized plate, make the door open easily and return to the position, align the four sides of the partition door with the line, make the door horizontal and vertical, and meet the requirements of the construction specification.
(6)清理打胶:打胶时应上下一条线,粗细一样,直角处没有多余的胶,其作用是保证隔板与墙体之间的更加牢固、密封。
(6) Cleaning and gluing: when gluing, the upper and lower lines shall be the same in thickness. There is no excess glue at the right angle. Its function is to ensure that the partition and the wall are more firm and sealed.
(7)安装完毕后指定专人看管,以防其他施工队伍在作业过程中损坏到本产品。
(7) After installation, special personnel shall be assigned to take care of the product to prevent other construction teams from damaging the product during operation.
(8)安装验收:安装完的济南卫生间隔断我方进行自检,经我方检验合格后报予监理、甲方进行验收。
(8) Installation acceptance: after the installation of Jinan toilet partition, we will conduct self inspection and report it to the supervisor and Party A for acceptance after passing our inspection.
以上便是问题的相关解答内容了,如果您想获取更多相关信息,就来关注我们网站http://www.jnndjc.com吧!
The above is the relevant answers to the questions. If you want to get more relevant information, please follow our website http://www.jnndjc.com Come on!
济南宁达建材有限公司

济南宁达建材有限公司

联系人:李经理

电话:15954121087   移动电话:15153190187

邮箱: 1499873208@qq.com

地址:山东省济南市天桥区小清河北路滨河商务中心D座24层2402

济南无障碍扶手哪家好?供应订做多少钱?济南临边防护栏怎么样?诚信公司专业以批发价格大量现货提供济南防护扶手、做卫生间隔断、无障碍扶手厂家、卫生间隔断怎么做等品质优良的产品,欢迎来电生产定制!
www.jnndjc.com(复制链接) 济南宁达建材有限公司