欢迎访问济南宁达建材有限公司!

济南宁达建材有限公司

联系人:李经理

电话:15954121087

地址:山东省济南市天桥区小清河北路8888号滨河商务中心D栋办公楼601—1室

当前位置:首页>新闻动态>>常见问题卫生间隔断施工需要哪些工艺流程?

卫生间隔断施工需要哪些工艺流程?

来源:http://www.jnndjc.com 日期:2022-02-24 发布人:admin
卫生间隔断的施工技术:
Construction technology of toilet partition:
1、现场检查:检查图纸的复制尺寸,核对图纸是否符合要求,检查瓷砖、洁具及其它相关成品是否有损坏,按照甲方和监理确认的施工图纸进行特殊工序施工。
1. On site inspection: check the copy size of the drawings, check whether the drawings meet the requirements, check whether the ceramic tiles, sanitary ware and other related finished products are damaged, and carry out special process construction according to the construction drawings confirmed by Party A and the supervisor.
2、派线:定位标记墙壁尺寸并保持水平。竖向及大面积区域应设置在两坑中间或按要求作业。
2. Setting out: locate and mark the wall size and keep it horizontal. Vertical and large area areas shall be set in the middle of two pits or operate as required.
3、安装标高:根据实测图纸检查卫生间的隔断安装的标高尺寸。
3. Installation elevation: check the elevation and size of partition installation in the toilet according to the measured drawings.
4、安装定位:根据标高,设计和监理确认的五金件铰链、门锁、把手、支架、横梁设计通过。使用安支架时,两侧的距离相同。当安有一个大的直角时,它保证在中间位置中间,上下两端保持在20厘米。根据情况有管道。测量腰线,然后打开,缝不超过0、1厘米直角。小心不要打碎墙砖或地砖。当安合页时,门的上下端应保持在20厘米左右,门的下端与中、小件的高度一致。在使用螺钉之前应该安装铰链螺钉,深应控制在1厘米以内。锁扣时,要注意如果有梯形锁芯,其位置距门的下端85厘米;如果有残障人士使用的凹槽,则应与带台阶锁的位置平行;锭梁要用螺丝或钉子固定在中小块上;铸锭的塑料板或铝片应用圆头螺钉固定在安;背面,注意塑料板和衬件应无缝、平整。
4. Installation and positioning: according to the elevation, the hardware hinges, door locks, handles, supports and beams confirmed by the designer and the supervisor are designed and passed. When using the safety bracket, the distance between both sides is the same. When there is a large right angle, it ensures that it is in the middle, and the upper and lower ends are kept at 20 cm. There are pipes according to the situation. Measure the waistline and then open it. The seam shall not exceed 0 or 1cm right angles. Be careful not to break wall or floor tiles. When installing hinges, the upper and lower ends of the door shall be kept at about 20cm, and the lower end of the door shall be consistent with the height of medium and small parts. Before using the screws, the hinge screws should be installed, and the depth should be controlled within 1 cm. When locking, pay attention that if there is a trapezoidal lock cylinder, its position is 85CM away from the lower end of the door; If there is a groove used by the disabled, it shall be parallel to the position with step lock; The ingot beam shall be fixed on the small and medium pieces with screws or nails; The plastic plate or aluminum sheet of the ingot shall be fixed in the installation position with round head screws; On the back, note that the plastic plate and lining shall be seamless and flat.
5、安装调试:门缝与支腿之间的距离应为2-2、5毫米,少要固定两个螺丝。门体的底部应该与中段的底部平齐,使门易于开启并回到合适的位置。隔离门四面齐,门应上下水平垂直,符合施工规范要求。
5. Installation and commissioning: the distance between the door seam and the outrigger shall be 2-2 and 5mm, and at least two screws shall be fixed. The bottom of the door body should be flush with the bottom of the middle section to make the door easy to open and return to the appropriate position. The isolation door shall be flush on all sides, and the door shall be horizontal and vertical from top to bottom, meeting the requirements of construction specifications.
6、清洁和涂胶:涂胶时,上下划一条线,厚度相同,直角处没有多余的胶水,其作用是保证隔墙与墙体之间的牢固和密封。
6. Cleaning and gluing: when gluing, draw a line from top to bottom with the same thickness. There is no excess glue at the right angle. Its function is to ensure the firmness and sealing between the partition wall and the wall.
7、安装完毕后,派专人负责,防止其他施工队在操作过程中损坏产品。
7. After installation, special personnel shall be assigned to prevent other construction teams from damaging products during operation.
8、安装验收:我们将对安,安装的卫生间的隔断进行自检,并向监理和甲方提交报告。
8. Installation acceptance: we will conduct self inspection on the partition of the installed toilet and submit a report to the supervisor and Party A.
以上就是今天带给大家的知识,济南卫生间隔断专注行业多年,为用户不断的提供有价值的内容,更多内容请继续关注我们:http://www.jnndjc.com
The above is the knowledge brought to you today. Jinan toilet partition has focused on the industry for many years and continuously provides users with valuable content. Please continue to pay attention to us for more content: http://www.jnndjc.com
济南宁达建材有限公司

济南宁达建材有限公司

联系人:李经理

电话:15954121087

邮箱: 1499873208@qq.com

地址:山东省济南市天桥区小清河北路8888号滨河商务中心D栋办公楼601—1室

www.jnndjc.com(复制链接) 济南宁达建材有限公司