步骤一:画线安装固定板
Step 1: draw a line to install the fixing plate
为了在墙上找到合适的位置来画出固定板的中线,通常在固定板上安装六个角代码,并根据需要将它们安装在板上。然后,在墙上的相应位置打孔,将塑料套放入孔中,然后用膨胀螺丝将固定板固定在墙上。
In order to find a suitable position on the wall to draw the center line of the fixed plate, usually install six corner codes on the fixed plate and install them on the plate as required. Then, drill holes in the corresponding positions on the wall, put the plastic sleeve into the holes, and fix the fixing plate on the wall with the expansion screws.
公共卫生间隔断
Public toilet partition
步骤二:安装调整底座
Step 2: install the adjusting base
根据预先设计好的施工图,在卫生间的地板上找到底座位置,画出中线,然后固定底座(底座位置离隔板边缘约3厘米)
According to the pre-designed construction drawing, find the base position on the floor of the toilet, draw the center line, and then fix the base (the base position is about 3cm away from the edge of the partition)
步骤三:安装隔间板
Step 3: install the compartment board
前两步是为安装隔板铺平道路。固定板和底座的作用是固定隔板。将隔板放在调节底座上,然后调节底座的高度,使隔板靠近墙上的固定板,然后微调底座的高度,使隔板与地面有一定的距离,约7厘米-10厘米。确定底座高度为1-1后,用水平尺确定水平,调整好一切后,用螺钉将隔板固定在固定板上和调整底座上。
The first two steps are to pave the way for the installation of partitions. The function of the fixing plate and the base is to fix the diaphragm. The clapboard is placed on the adjusting base, then the height of the base is adjusted, so that the clapboard is near the fixed plate of the wall, and the height of the base is fine-tuning, so that the baffle plate has a certain distance from the ground, about 7 centimeters -10 cm. After the height of the base is determined to be 1-1, the level shall be determined with a level ruler. After everything is adjusted, the partition plate shall be fixed on the fixing plate and the base shall be adjusted with screws.
公共步骤四:安装拉杆
Public step 4: install the pull rod

根据隔间的实际长度进行切割和固定。当水平连接直拉杆时,管道需要配备圆形连接套管和紧急连接弹簧片,以确保接头平整牢固。连接应在上部张力固定件,以增加美观。对于车厢内的90度转角拉杆,采用铝合金注射成型的90度转角接头连接转角两端的拉杆。终端拉杆用凸圆壁固定套和螺钉固定在墙面上。用螺钉将拉杆连接并固定在立柱的上缘固定件上。
Cut and fix according to the actual length of the compartment. When connecting the straight rod horizontally, the pipe needs to be equipped with a circular connecting sleeve and an emergency connecting spring plate to ensure that the joint is flat and firm. Connections shall be made at the upper tension fixings to increase aesthetics. For the 90 degree angle rod in the carriage, the 90 degree angle joint of aluminum alloy injection molding is used to connect the rod at both ends of the angle. The end tie rod is fixed on the wall with convex and round wall fixing sleeve and screw. Connect the pull rod with screws and fix it on the upper edge fastener of the column.
步骤五:安装立柱
Step 5: install the column
拉杆固定件用螺钉固定在立柱中间的顶端,立柱和隔板固定组合成一个墙边立柱——在墙面上画一条垂直于地面的直线,用电钻在直线的三个外侧钻孔,孔内套有预埋塑料塞,确定垂直于地面后,用带螺钉的L形固定件将墙侧立柱固定在离地面145的墙上。端子立柱-将上边缘拉杆固定件和l形边缘连接件固定在端子立柱上,然后用螺钉将板固定在隔板上
The pull rod fixing part is fixed at the top of the middle of the column with screws, and the column and the partition are fixed and combined into a wall side column - draw a straight line perpendicular to the ground on the wall surface, drill holes on the three outer sides of the straight line with electric drill, and the holes are covered with embedded plastic plugs. After confirming that they are perpendicular to the ground, fix the wall side column on the wall 145 away from the ground with L-shaped fixing parts with screws. Terminal post - secure the upper edge tie rod fixings and L-edge connections to the terminal post and screw the board to the bulkhead
公共卫生间隔断
Public toilet partition
步骤六:安装门扇
Step 6: install the door leaf
将铰链固定在立柱上,通常为2-3个,然后将相应数量的铰链安装在门扇上相应的位置,轻轻抬起门扇,将自动返回尼龙座放在铰链座中,调整位置,打开和关闭门,检查门扇是否可以自由地打开和关闭,检查和调整直到满意。
Fix the hinge on the column, usually 2-3, then install the corresponding number of hinges on the door leaf at the corresponding position, lift the door leaf gently, place the automatic return nylon seat in the hinge seat, adjust the position, open and close the door, check whether the door leaf can be opened and closed freely, check and adjust until it is satisfied.
With the summary above the toilet partition in Jinan, I hope it can help our customers. If you don't understand or ask for help, please click our website: http://www.jnndjc.com Or call for consultation, we will do our best to solve it for you